Datasheet for Steel Grades Carbon Steel AISI 6152Steel GradeAISI 6152 Chemical information,Mechanical properties Physical properties, Mechanical properties, Heat treatment, and Micro structure This page is mainly introduced the AISI 6152 Datasheet, including chemical information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc.AISI 6152 - Structural steel for DIN,EN,AISI,JIS,BS,NFA , aisi 6152 carbon steel material1, Quenched and tempered steel such as the carbon content of steel is generally about 0.25% ~ 0.25%, for a given cross section size of the structure, the tempering treatment, quenching and tempering, if along the cross section of hardening, the performance is good, if quenching, have ferrite in microstructure, the toughness is reduced.With temper brittleness tendency of steel such as manganese steel
General characteristics of Alloy Steel 6150. A similar alloy to 5150 with a small, but effective, vanadium addition. ApplicationsAISI 6150 Alloy Steel (UNS G61500) - Materials EngineeringAlloy steels are designated by AISI four-digit numbers. They are more susceptible to mechanical and heat treatments than carbon steels. They comprise different types of steels with compositions which exceed the limitations of B, C, Mn, Mo, Ni, Si, Cr, and Va in the carbon steels.AISI/SAE Steel - Numbering System - Engineering ToolBoxAISI/SAE steel numbers. Sponsored Links. AISI/SAE steel numbers are indicated below. the first digit indicates that this is plain carbon steel. the second digit indicates there are no alloying elements. the last two digits indicates that the steel contains approximately 0.20 percent carbon.
See more on worldsteelgrades, aisi 6152 carbon steel materialASTM A36 Carbon Steel vs. SAE-AISI 1020 Steel , aisi 6152 carbon steel materialASTM A36 Carbon Steel vs. SAE-AISI 1020 Steel. Both ASTM A36 carbon steel and SAE-AISI 1020 steel are iron alloys. Their average alloy composition is basically identical. There are 30 material properties with values for both materials. Properties with values for just one material (1, in this case) are not shown. For each property being compared,, aisi 6152 carbon steel materialASTM SAE AISI 1045 Carbon Steel Heat Treatment, Chemical , aisi 6152 carbon steel materialC1045 is also known as 1045 cold rolled steel (cold worked), and 1045 hot rolled steel is known as 1045 HR. Applications. AISI SAE 1045 material is widely used in industrial applications where higher wear resistance and strength are required, typical applications including: Light gears, shafts, axles, spindles, pins, guide rods, connecting rods, bolts, worms, crankshafts, machine components, etc.
Grades for alloy steels and carbon steels were identified by this system based on standard chemical compositions. A discontinuity in the relationship between grade designations and the AISI occurred as a result of the decision made by the AISI to stop writing material specifications. Grading of AISI MaterialsSAE steel grades - WikipediaThe SAE steel grades system is a standard alloy numbering system for steel grades maintained by SAE International. In the 1930's and 1940's, the American Iron and Steel Institute and SAE were both involved in efforts to standardize such a numbering system for steels. These efforts were similar and overlapped significantly. For several decades the systems were united into a joint system designated the SAE/AISI Carbon & Alloy Steel Name System - Otai Special SteelSAE/AISI Carbon & Alloy Steel Name System. Alloy steels and carbon steels for a number of years were designated with specific grades by a four-digit SAE/AISE numerical index system. Grades for alloy steels and carbon steels were identified by this system based on standard chemical compositions.
AISI/SAE steel numbers are indicated below. Example AISI/SAE No. 1020. the first digit indicates that this is plain carbon steel. the second digit indicates there are no alloying elements; the last two digits indicates that the steel contains approximately 0.20 percent carbon ; Example AISI/SAE No. 4340Carbon Steel: Properties, Examples and Applications - Carbon steel is an iron-carbon alloy, which contains up to 2.1 wt.% carbon. For carbon steels, there is no minimum specified content of other alloying elements, however, they often contain manganese. The maximum manganese, silicon and copper content should SAE-AISI 1527 (formerly 1027, G15270) Carbon Steel , aisi 6152 carbon steel materialSAE-AISI 1527 (formerly 1027, G15270) Carbon Steel. SAE-AISI 1527 steel is a resulfurized carbon steel formulated for primary forming into wrought products. 1527 is the designation in both the SAE and AISI systems for this material. G15270 is the UNS number. Older literature may refer to this material as AISI 1027, but this is now discouraged.
Alloy Steel 6150 Grade Summary: High carbon, chromium-vanadium, commercial quality alloy steel with higher strength and hardness. When heat treated, the material has excellent toughness, shock resistance, and water/abrasion resistance.eFunda: Listing of AISI 10xx Carbon SteelsMaterials » Alloys » Steel » Carbon Steel » ASTM A516 Grade 70. Materials » Alloys » Steel » Carbon Steel » AISI 1049. Materials » Alloys » Steel » Carbon Steel » ASTM A455 Type IAISI 1215 Carbon Steel (UNS G12150)AISI 1215 Carbon Steel (UNS G12150) Steel News - Published on Thu, 04 Oct 2012 , aisi 6152 carbon steel material Carbon steels are designated by AISI four digit numbers. They contain carbon as the significant alloying element , aisi 6152 carbon steel material
Low Carbon Steel AISI 1522. Buy AISI 1522 bolts, nuts and other fasteners from Boltport, an Indian manufacturer & supplier of AISI 1522 bolting materials to ASTM B446, B564, F467, F468, UNS N06600, DIN EN 2.4856, AMS 5666 and BS 3076 specifications with properties adequate for high strength, corrosion resistant and high temperature applications up to 1000º C (1800º F).Material Category Search - Online Materials Information , aisi 6152 carbon steel materialInstructions: This page allows you to quickly access all of the polymers/plastics, metals, ceramics, fluids, and other engineering materials in the MatWeb material property database. Just select the material category you would like to find from the tree. Click on the [+] AISI 1045 Carbon Steel - AISI 1045 Medium Carbon Steel , aisi 6152 carbon steel materialC1045 is a medium carbon, medium tensile steel supplied as forged or normalized. This steel shows reasonable strength and toughness. C1045 will through harden to 2.5 (63mm) with a tensile strength of 66-120 Ksi (620-850 MPa). Contact All Metals & Forge Group for your forging needs.
AISI 1045 steel is a medium carbon steel which is recognized for its good tensile strength and hardness. It is also popular because of its ability to be machined easily . Machining processes like milling, turning, tapping and broaching can be performed without any problems.SAE/AISI Carbon & Alloy Steel Name System - Otai Special SteelCarbon Steel Handbook - Metabunkweldability, carbon steel is one of the most commonly used materials in the electric power generation industry. Carbon steels in which carbon represents 0.150.35%those used most often as boiler and piping materialsare the focus of this Carbon Steel Handbook. Although carbon steel is available in virtually all product forms, it is the