34CrMo4 Steel is a high quality Quenched and Tempered Alloy Structural steel, It belong to the high quality low carbon,Low alloy chromium, molybdenum, nickel case hardening steel. Oil Quenched & Tempered Hardness is 18-22 HRc. Annealing delivery hardenss less than 250HB. With a lower carbon content range, So have good weldability.35CrMo4 (UNI ) - Worldwide equivalent grades35CrMo4 (Italy, UNI) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Buy, sell, suppliers search product 35CrMo4 on-line35CrMo4 Chemical Composition,35CrMo4 Mechanical , 35crmo4Bebon steel can supply 35CrMo4 Chemical Composition,35CrMo4 Mechanical Characteristics price and specification ,we are steel suppliers and manufacturer,you can contact us to get 35CrMo4 Chemical Composition,35CrMo4 Mechanical Characteristics application and other informations.
This page cover the 35CrMo steel grades Mechanical Properties, Chemical Element, Cross Reference of China GBT 35CrMo Materials, Application China structural steel and alloy steel,Mechanical Properties of 35CrMoA Steel at High Strain Rate , 35crmo4The tensile properties of alloy steel 35CrMoA were measured by dynamic tension experimental apparatus, and the stress-strain curves of the material at strain rate range from 10 -2 /s to 10 3 /s were obtained. The fracture appearance and metallurgical structure (PDF) Microstructure and adhesion of 100Cr6 steel coatings , 35crmo4Abstract Thermally sprayed of 100Cr6 steel coatings are widely used to combat degradation of components and structures due to mechanical wear. In this
Weldability: Low weldability; this steel grade can be welded only with suitable precautions. Hardenability: Steel grade with medium carbon content showing a poor hardenability; sensitive to notching and to quenching cracks.34CrMo4, 1.7220, AISI 4135 - Structural steelmaterial Grade Comparison TableMARYLAND METRICS Technical Data Chart A short general listing of popular materials International Material Grade Comparison Table The standards that correspond with DIN Material Numbers can only be compared approximately. The use of these equivalents has to be evaluated on a case-by-case basis.
1.7220 34CrMo4 708A37 19B 35CD4 35CrMo4 34CrMo4 2234 4137 4135 35CrMo SCM 440 1.7223 41CrMo4 708M40 19A 42CD4TS 41CrMo4 42CrMo4 2244 4140 4142 40CrMoA SCM440(H) 1.7225 42CrMo4 708M40 19A 42CD4 42CrMo4 42CrMo4 2244 4140 42CrMo 42CrMnMo 1.7361 32CrMo12 722M24 40B 30CD12 32CrMo12 F.124.A 2240 F 0 F - dew-stahl, 35crmo435crmo4 une f.8331 f.8231 jis scm432 scm435 h ss 2234 gost as38chgm 35chm 35chml aisi / sae / astm 4135 4137. werkstoffdatenblatt 3cm 3cms 10 1 firmodur 7220 / firmodur 7226 mechanische eigenschaften bei raumtemperatur im vergÜteten zustand (+qt) nach din en 10083-3 , 35crmo435CrMo4 STAS :: Total Materia
Pehled vlastností oceli 42CrMo4 ( 42CrMoS4 ) 1.7225 (1.7227) Druh oceli Nízkolegovaná ulechtilá chrom - molybdenová ocel k zulechování TDP SN EN 10083-3: 2007 Dívjí oznaení 42CrMo4 ( 42CrMoS4 ) podle SN EN 10083-1: 1991+A1: 1996; 42CrMo4 ( Hot Rolled 35CrMo4 Alloy Steel Round Bar, View 35crmo4 , 35crmo4Hot Rolled 35CrMo4 Alloy Steel Round Bar, US $ 1,650 - 1,800 / Metric Ton, Alloy Steel, AISI, ASTM, BS, DIN, GB, JIS, Diameter:10-1000mm.Source from Sichuan Liaofu , 35crmo4K-nut 5/16"-24 (6 point), K-NUTS, 35crmo4.3125-24 k-nuts are typically used for medium components. Imperial self locking nut made of 35CrMo4, 1100 MPa, 235 °C = 455 °F, MoS2 low friction coating.
Pehled vlastností oceli 42CrMo4Pehled vlastností oceli 42CrMo4 ( 42CrMoS4 ) 1.7225 (1.7227) Druh oceli Nízkolegovaná ulechtilá chrom - molybdenová ocel k zulechování TDP SN EN 10083-3: 2007 Dívjí oznaení 42CrMo4 ( 42CrMoS4 ) podle SN EN 10083-1: 1991+A1: 1996; 42CrMo4 ( ASTM A366 ASTM A1008 Steel - Stainless Steel Tubing , 35crmo4ASTM A366 ASTM A1008 Steel. AISI 1008 is a Standard grade Carbon Steel. It is composed of (in weight percentage) 0.10%(max) Carbon (C), 0.30-0.50% Manganese (Mn), 0.04%(max) Phosphorus (P), 0.05%(max) Sulfur (S), and the base metal Iron (Fe). Other designations of AISI 1008 carbon steel include UNS G10080 and AISI 1008.
ASTM A36 Standard Specification for Carbon Structural Steel covers carbon structural steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes. Heat analysis shall be used to determine the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, and copper.(PDF) Hydrogen Embrittlement (HE) Susceptibility of High , 35crmo4Hydrogen embrittlement (HE) susceptibilities of two different grades of tempered martensite steels 35CrMo4 and 41Cr4 were determined by using the incremental step load (ISL) technique.Aubert & Duval - Forgings, powders and bars in high , 35crmo4Aubert & Duval designs and processes superalloys, high performance steels, aluminum and titanium alloys in the form of bars, powders and forgings.